- **High-Speed Sampling:** - 65 MS/s per channel simultaneous sampling - Up to 130 MS/s in single-channel ping-pong mode - **High Resolution:** - 14-bit analog-to-digital conversion for precise waveform capture - **Deep Onboard Memory:** - Standard 128 MB SDRAM, expandable to 512 MB SODIMM SDRAM - 3k-sample FIFO buffer for real-time streaming - **Flexible Input Configuration:** - Two simultaneous-sampled single-ended analog input channels - Programmable input ranges: ±1 V or ±5 V - Selectable input impedance: 50 Ω or 1.5 MΩ - **Wide Bandwidth:** - Minimum 30 MHz (-3 dB) analog input bandwidth - **Advanced Triggering:** - Supports software, analog, digital, and SSI triggers - Trigger modes: pre-trigger, post-trigger, middle-trigger, delay-trigger - Repeated trigger acquisition with 2-cycle rearming interval - **Multiple Device Synchronization:** - System Synchronization Interface (SSI) for timing and trigger sharing across multiple boards - **Auto-Calibration:** - Fully automated offset and gain calibration using onboard DACs - Calibration constants stored in EEPROM - **Bus Mastering DMA:** - Scatter-gather DMA for efficient data transfer to host memory - **Software Support:** - Drivers for Windows and Linux (WD-DASK, WD-DASK/X) - LabVIEW® and ActiveX (WD-LVIEW, WD-OCX) support - DAQBench™ ActiveX controls for rapid application development - **Compact Design:** - Half-size PCI card (175 mm × 107 mm)

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PCI

- **High-Speed Sampling:** - 65 MS/s per channel (dual-channel mode) - 130 MS/s (single-channel ping-pong mode) - **High Resolution:** 14-bit A/D conversion for precise waveform digitization. - **Deep Onboard Memory:** - 128 MB standard SODIMM SDRAM - Expandable up to 512 MB for extended waveform recording. - **Flexible Input Configuration:** - Two simultaneous-sampled single-ended analog inputs. - Programmable input ranges: ±1 V or ±5 V. - Selectable input impedance: 50 Ω or 1.5 MΩ. - **Wide Bandwidth:** Minimum 30 MHz (-3 dB), suitable for high-frequency signal acquisition. - **Advanced Triggering:** - Supports software, analog, digital, and SSI triggers. - Trigger modes: pre-trigger, post-trigger, middle-trigger, delay-trigger. - Repeated trigger acquisition with 2-cycle rearming interval. - **Multiple Device Synchronization:** - System Synchronization Interface (SSI) for timing and trigger sharing across multiple boards. - **Auto-Calibration:** - Fully automated offset and gain calibration using onboard reference DACs. - Calibration constants stored in EEPROM. - **Efficient Data Transfer:** - Scatter-gather bus mastering DMA for high-throughput data transfer. - 3k-sample FIFO for real-time streaming when SDRAM buffering is unnecessary. - **Software Support:** - Drivers for Windows (WD-DASK), Linux (WD-DASK/X), LabVIEW® (WD-LVIEW), and ActiveX (WD-OCX). - Compatible with ADLINK DAQBench™ for visualization and automation. - **Compact Design:** Half-size PCI card (175 mm × 107 mm). - **Plug-and-Play Configuration:** Automatic IRQ and address assignment via PCI BIOS.

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PCI

- **High-Speed Sampling:** - 65 MS/s per channel simultaneous sampling. - Up to 130 MS/s in single-channel ping-pong mode. - **High Resolution:** - 14-bit analog-to-digital conversion for precise waveform digitization. - **Deep Onboard Memory:** - Standard 128 MB SDRAM, expandable to 512 MB SODIMM SDRAM. - 3k-sample FIFO buffer for real-time streaming. - **Flexible Input Configuration:** - Two simultaneous-sampled single-ended analog input channels. - Programmable input ranges of ±1 V and ±5 V. - Selectable input impedance: 50 Ω or 1.5 MΩ. - **Wide Bandwidth:** - Minimum -3 dB bandwidth of 30 MHz per channel. - Input coupling: DC. - **Advanced Triggering:** - Supports software, analog, digital, and SSI triggers. - Trigger modes: pre-trigger, post-trigger, middle-trigger, delay-trigger. - Repeated trigger acquisition with 2-cycle rearming interval. - Analog trigger sensitivity: 256 steps across full-scale range. - Digital trigger compatibility: 5 V TTL, minimum pulse width 10 ns. - **Multiple Device Synchronization:** - System Synchronization Interface (SSI) for multi-card synchronization. - Common trigger and timebase sharing across multiple PCI-9820 boards. - **Auto-Calibration:** - Fully software-controlled calibration using onboard trim DACs. - Calibration constants stored in EEPROM. - Reference voltage: +5.000 V, drift ±2 ppm/°C, stability 6 ppm/1000 hrs. - **Bus Interface:** - 32-bit, 33 MHz PCI bus (3.3 V or 5 V signaling). - Scatter-gather bus mastering DMA for efficient data transfer. - **Compact Design:** - Half-size PCI form factor (175 mm × 107 mm).

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PCI

- **High‑Speed Sampling:** 4 simultaneous 16‑bit ADC channels, each capable of up to **20 MS/s** sampling rate. - **Deep Onboard Memory:** **512 MB SDRAM** shared across channels for long waveform recording independent of PCI bus bandwidth. - **Programmable Input Range:** Software‑selectable **±1 V or ±5 V** input range for flexible signal scaling. - **Selectable Input Impedance:** **50 Ω or 1 MΩ** input impedance, software‑configurable for high‑frequency or high‑impedance sources. - **Wide Analog Bandwidth:** Typical **9.6 MHz (‑3 dB)** bandwidth at 50 Ω input impedance. - **Flexible Triggering:** Supports software, external digital, and analog triggers, as well as PXI STAR and PXI Trigger Bus sources. - **Multiple Trigger Modes:** Post‑trigger, pre‑trigger, middle‑trigger, delay‑trigger, and re‑trigger acquisition modes. - **Multi‑Module Synchronization:** Synchronize multiple digitizers via PXI Trigger Bus or SSI interface for scalable systems. - **Auto‑Calibration:** Built‑in precision 5 V reference with ±3 ppm/°C drift for fully automated calibration. - **Scatter‑Gather DMA:** Efficient high‑throughput data transfer to host memory without large contiguous buffers. - **PXI and PCI Compatibility:** Available in both PXI 3U Eurocard and standard PCI half‑length form factors. - **Software Support:** Compatible with ADLINK DAQPilot, DAQMaster, and WD‑DASK drivers for Windows, LabVIEW®, and MATLAB®. - **High Dynamic Performance:** Typical SINAD 78.6 dBc, SFDR 88.9 dBc, and ENOB 12.77 bits at 20 MS/s.

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PCI

- **High‑Speed Sampling:** Up to **40 MS/s per channel** simultaneous sampling across four channels. - **High Resolution:** **16‑bit ADC** resolution (1 in 65,536) for precise signal digitization. - **Wide Bandwidth:** Typical **20 MHz (‑3 dB)** analog input bandwidth at 50 Ω. - **Deep Onboard Memory:** **512 MB SDRAM** shared across four channels for extended waveform capture. - **Flexible Input Configuration:** - Software‑selectable **input impedance**: 50 Ω or 1 MΩ. - Programmable **input voltage ranges**: ±0.2 V or ±1 V. - DC coupling for accurate low‑frequency measurements. - **Multiple Trigger Sources:** Software, external digital (SMB), analog threshold (CH0–CH3), PXI STAR, PXI Trigger Bus, and SSI bus. - **Trigger Modes:** Post‑trigger, pre‑trigger, middle‑trigger, delay‑trigger, and re‑trigger acquisition. - **Clock Sources:** Internal oscillator (40 MHz), external clock via SMB, PXI STAR, PXI Trigger Bus, PXI 10 MHz, or SSI bus. - **Scatter‑Gather DMA:** Efficient high‑throughput data transfer to host memory. - **Auto‑Calibration:** Built‑in precision 5 V reference with ±3 ppm/°C drift for software‑controlled calibration. - **Multi‑Module Synchronization:** PXI Trigger Bus or SSI interface for synchronized operation of multiple digitizers. - **Software Support:** DAQPilot, DAQMaster, and WD‑DASK drivers for Windows, LabVIEW®, and MATLAB®. - **Form Factor:** Standard height, half‑length PCI card (167.64 mm × 106.68 mm). - **Plug‑and‑Play PCI Interface:** 32‑bit/66 MHz PCI bus supporting both 3.3 V and 5 V signaling.

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PCI

- **High-Speed Sampling:** Up to **40 MS/s per channel** simultaneous sampling across four channels. - **High Resolution:** 16-bit ADC resolution (1 part in 65,536). - **Large Onboard Memory:** 512 MB SDRAM for long-duration waveform capture independent of PCI bus bandwidth. - **Wide Bandwidth:** 20 MHz (-3 dB typical) analog input bandwidth at 50 Ω input impedance. - **Flexible Input Configuration:** Software-selectable **50 Ω or 1 MΩ input impedance**; DC coupling. - **Programmable Input Ranges:** ±1 V or ±5 V (software selectable). - **Multiple Trigger Sources:** Software, external digital (SMB), analog threshold, PXI STAR, PXI Trigger Bus, and SSI bus. - **Trigger Modes:** Post-trigger, pre-trigger, middle-trigger, delay-trigger, and re-trigger acquisition. - **Multi-Module Synchronization:** Supports synchronization via PXI Trigger Bus or SSI interface for multi-board operation. - **Auto Calibration:** Built-in precision 5 V reference with ±3 ppm/°C drift for software-controlled self-calibration. - **Scatter-Gather DMA:** Efficient high-speed data transfer to host memory without large contiguous memory blocks. - **PCI Interface:** 32-bit, 66 MHz PCI bus supporting both 3.3 V and 5 V signaling. - **Comprehensive Software Support:** Compatible with ADLINK DAQPilot, DAQMaster, and WD-DASK drivers for Windows, LabVIEW®, and MATLAB®. - **Compact Form Factor:** Standard height, half-length PCI card for easy integration into desktop or industrial PCs.

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PCI

- **High-Resolution Digitization:** 16-bit ADC resolution across four simultaneous single-ended channels. - **Sampling Rate:** Up to 10 MS/s per channel (PXI-9816D model). - **Deep Onboard Memory:** 512 MB SDRAM shared across four channels, enabling long-duration waveform recording independent of PCI/PXI bus transfer rates. - **Programmable Input Range:** Software-selectable ±0.2 V or ±1 V input ranges for optimal dynamic range and signal fidelity. - **Selectable Input Impedance:** Software-configurable 50 Ω or 1 MΩ input impedance for flexible signal interfacing. - **Flexible Triggering:** Supports software, external digital, analog, PXI STAR, and PXI Trigger Bus triggers with multiple trigger modes (pre-, post-, middle-, delay-, and re-trigger). - **Synchronization:** Multi-module synchronization via PXI Trigger Bus or SSI interface for scalable, time-aligned data acquisition systems. - **Auto-Calibration:** Built-in precision 5 V reference with ±3 ppm/°C drift for fully automated calibration and long-term accuracy. - **High Dynamic Performance:** Typical SFDR of 90 dBc, SINAD of 79 dBc, and ENOB of 12.8 bits. - **PXI 3U Eurocard Form Factor:** Compact 160 mm × 100 mm module compatible with standard PXI chassis. - **Software Support:** Comprehensive driver suite including DAQPilot, DAQMaster, and WD-DASK for Windows, LabVIEW®, and MATLAB® environments.

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PXI/PXIe

- **High-Resolution Digitization:** 16-bit ADC resolution providing precise signal representation with up to 12.8-bit effective number of bits (ENOB). - **Sampling Rate:** Up to 10 MS/s per channel with simultaneous sampling across four channels. - **Deep Onboard Memory:** 512 MB SDRAM shared across channels for extended waveform recording independent of PCI bus bandwidth. - **Programmable Input Range:** Software-selectable ±1 V or ±5 V input range for flexible signal conditioning. - **Selectable Input Impedance:** Software-configurable 50 Ω or 1 MΩ input impedance for compatibility with various signal sources. - **Flexible Triggering:** Supports software, external digital, analog, PXI STAR, and PXI Trigger Bus triggers with multiple trigger modes (pre-, post-, middle-, delay-trigger). - **Synchronization Support:** PXI Trigger Bus and SSI interface enable multi-module synchronization for complex measurement systems. - **Auto-Calibration:** Built-in precision reference with ±3 ppm/°C drift for stable calibration and long-term accuracy. - **High Dynamic Performance:** Typical SFDR of 90 dBc, SINAD of 79 dBc, and THD below -89 dBc at 1 MHz input frequency. - **Software Integration:** Compatible with ADLINK DAQPilot, DAQMaster, and WD-DASK drivers for Windows, LabVIEW®, and MATLAB®. - **Compact PXI Form Factor:** 3U Eurocard module (100 mm × 160 mm) for easy integration into PXI chassis.

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PXI/PXIe

- **High-Speed Sampling:** - Dual-channel simultaneous sampling at up to 65 MS/s per channel. - Single-channel “ping-pong” mode supports up to 130 MS/s. - **High Resolution:** - 14-bit A/D conversion for precise signal digitization. - **Deep Onboard Memory:** - 128 MB standard SODIMM SDRAM, expandable to 512 MB. - 3k-sample FIFO for real-time streaming. - **Flexible Input Configuration:** - Programmable input ranges of ±1 V and ±5 V. - Selectable input impedance: 50 Ω or 1.5 MΩ. - **Triggering Flexibility:** - Supports software, analog, digital, and SSI (System Synchronization Interface) triggers. - Trigger modes include pre-trigger, post-trigger, middle-trigger, and delay-trigger. - Repeated trigger acquisition with minimal rearming interval (2 timebase cycles). - **Synchronization Capability:** - SSI bus for multi-module synchronization using shared clock and trigger signals. - **Auto-Calibration:** - Fully automated offset and gain calibration using onboard DACs. - Calibration constants stored in EEPROM for persistent accuracy. - **Data Transfer Efficiency:** - Scatter-gather bus mastering DMA for high-throughput data transfer to host memory. - **Robust Design:** - Compact PXI form factor with BNC and SMB connectors. - Operating temperature range: 0°C to 50°C.

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PXI/PXIe

- **High-Speed Sampling:** - 65 MS/s simultaneous sampling on two channels. - 130 MS/s single-channel sampling in ping-pong mode. - **High Resolution:** - 14-bit A/D conversion for precise waveform digitization. - **Deep Onboard Memory:** - 512 MB SODIMM SDRAM for extended waveform recording. - 3k-sample FIFO for real-time streaming. - **Flexible Input Configuration:** - Programmable input ranges of ±1 V and ±5 V. - Selectable input impedance: 50 Ω or 1.5 MΩ. - **Triggering Flexibility:** - Supports software, analog, and digital triggers. - Trigger modes: pre-trigger, post-trigger, middle-trigger, delay-trigger. - Repeated trigger acquisition with 2-cycle rearming interval. - **Synchronization Capability:** - System Synchronization Interface (SSI) for multi-module synchronization. - Common trigger and timebase sharing across multiple PXI-9820 modules. - **Auto-Calibration:** - Fully automated offset and gain calibration using onboard DACs. - Calibration constants stored in EEPROM for long-term stability. - **Data Transfer Efficiency:** - Scatter-gather bus mastering DMA for high-speed data transfer to host memory. - Real-time transfer bypassing SDRAM when bandwidth allows. - **Robust Design:** - Compact PXI form factor with plug-and-play configuration. - Integrated DC/DC converter for stable operation.

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PXI/PXIe

- **High-Speed Sampling:** 20 MS/s per channel simultaneous sampling across four channels. - **High Resolution:** 16-bit ADC resolution (1 part in 65,536). - **Deep Onboard Memory:** 512 MB SDRAM shared across channels for extended waveform recording. - **Programmable Input Range:** ±0.2 V or ±1 V, software selectable. - **Selectable Input Impedance:** 50 Ω or 1 MΩ, software controlled. - **Wide Bandwidth:** Typical -3 dB bandwidth of 9.6 MHz at ±1 V input range. - **Flexible Triggering:** Supports software, external digital, analog, PXI STAR, and PXI Trigger Bus triggers. - **Multiple Trigger Modes:** Post-trigger, pre-trigger, middle-trigger, delay-trigger, and re-trigger acquisition. - **Multi-Module Synchronization:** PXI Trigger Bus and PXI STAR support for synchronized operation across multiple modules. - **Auto Calibration:** Built-in precision 5 V reference with ±3 ppm/°C drift for software-controlled calibration. - **Scatter-Gather DMA:** Efficient data transfer to host memory without CPU overhead. - **PXI 3U Form Factor:** Compact, modular design for PXI chassis integration. - **Software Support:** Compatible with ADLINK DAQPilot, DAQMaster, and WD-DASK drivers for Windows, LabVIEW®, and MATLAB® environments.

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PXI/PXIe

- **High‑Speed, High‑Resolution Acquisition:** Four simultaneous 16‑bit ADC channels with sampling rates up to **40 MS/s** per channel. - **Deep Onboard Memory:** **512 MB SDRAM** shared across channels allows long waveform recording independent of PCI/PXI bus throughput. - **Programmable Input Range and Impedance:** Software‑selectable **±0.2 V or ±1 V** input ranges; switchable **50 Ω or 1 MΩ** input impedance for flexible signal interfacing. - **Wide Bandwidth:** Typical **20 MHz (‑3 dB)** analog input bandwidth at 50 Ω impedance. - **Flexible Triggering:** Supports **software, external digital, analog, PXI STAR, PXI Trigger Bus, and SSI** trigger sources. Trigger modes include **pre‑trigger, post‑trigger, middle‑trigger, delay‑trigger, and re‑trigger** operation. - **Multi‑Module Synchronization:** PXI Trigger Bus and STAR Trigger support enable precise synchronization of multiple modules. - **Auto‑Calibration:** Built‑in precision 5 V reference with ±3 ppm/°C drift ensures stable calibration and accuracy across temperature variations. - **Scatter‑Gather DMA:** Efficient data transfer using non‑contiguous memory blocks for high‑throughput acquisition. - **Software Support:** Compatible with **DAQPilot**, **DAQMaster**, and **WD‑DASK** drivers for Windows, LabVIEW®, MATLAB®, and ActiveX environments. - **Compact PXI Form Factor:** 3U Eurocard (100 mm × 160 mm) module with front‑panel BNC and SMB connectors.

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PXI/PXIe

- **High‑Speed Sampling:** 40 MS/s per channel simultaneous sampling across four 16‑bit ADCs. - **High Resolution:** True 16‑bit resolution (1 in 65,536) for accurate signal representation. - **Wide Bandwidth:** Typical –3 dB bandwidth of 20 MHz (50 Ω input) and up to 80 MHz for ±1 V range. - **Large Onboard Memory:** 512 MB SDRAM shared across four channels for long acquisition sessions. - **Programmable Input Range:** Software‑selectable ±0.2 V or ±1 V (also ±1 V/±5 V for H‑variants). - **Selectable Input Impedance:** 50 Ω or 1 MΩ, software‑configurable for flexible signal interfacing. - **Flexible Triggering:** Supports software, external digital, analog, PXI STAR, and PXI Trigger Bus triggers. - **Multiple Trigger Modes:** Post‑trigger, pre‑trigger, middle‑trigger, delay‑trigger, and re‑trigger operation. - **Multi‑Module Synchronization:** PXI Trigger Bus and SSI interface enable precise synchronization of multiple modules. - **Auto‑Calibration:** Built‑in precision 5 V reference with ±3 ppm/°C drift for fully automated calibration. - **Scatter‑Gather DMA:** Efficient high‑throughput data transfer to host memory without fragmentation. - **PXI Integration:** Full compliance with PXI 3U Eurocard mechanical and electrical standards. - **Software Support:** Compatible with ADLINK DAQPilot, DAQMaster, and WD‑DASK drivers for Windows, LabVIEW®, and MATLAB®. - **High Dynamic Performance:** Typical SINAD 76 dBc, SFDR 91.6 dBc, ENOB 12.3 bits at 40 MS/s. - **Compact Form Factor:** Single‑slot 3U PXI module (100 × 160 mm).

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PXI/PXIe

- **High-Speed Sampling:** 40 MS/s per channel simultaneous sampling across four channels. - **High Resolution:** 16-bit ADC resolution (1 part in 65,536). - **Large Onboard Memory:** 512 MB SDRAM shared across channels for long-duration waveform recording. - **Programmable Input Range:** ±1 V or ±5 V, software selectable. - **Selectable Input Impedance:** Software-selectable 50 Ω or 1 MΩ input impedance. - **Wide Bandwidth:** Typical -3 dB bandwidth of 20 MHz at 50 Ω input impedance. - **Flexible Triggering:** Supports software, external digital, analog, PXI STAR, and PXI Trigger Bus triggers. - **Multiple Trigger Modes:** Post-trigger, pre-trigger, middle-trigger, delay-trigger, and re-trigger acquisition. - **Multi-Module Synchronization:** PXI Trigger Bus and SSI interface for synchronized operation across multiple modules. - **Auto Calibration:** Built-in precision 5 V reference with ±3 ppm/°C drift for software-controlled self-calibration. - **Scatter-Gather DMA:** Efficient data transfer to host memory without CPU overhead. - **PXI 3U Eurocard Form Factor:** Compact 160 mm × 100 mm module for PXI chassis integration. - **Plug-and-Play Configuration:** Fully compliant with PXI specifications for automatic resource allocation.

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PXI/PXIe

- **PXI Express Specification Rev. 1.0 Compliant** – Ensures full interoperability with PXIe chassis and controllers. - **Eight Simultaneous Analog Inputs** – Each channel sampled concurrently for phase‑coherent measurements. - **24‑Bit Sigma‑Delta ADCs** – High‑resolution conversion with superior dynamic range and low noise. - **Sampling Rate:** Up to 192 kS/s per channel. - **Input Range:** ±10 V or ±1 V, software‑selectable. - **AC/DC Coupling:** Software‑selectable with 0.5 Hz cutoff frequency for AC mode. - **Integrated IEPE Excitation:** 4 mA constant current per channel, 24 V compliance, for accelerometers and microphones. - **Auto‑Calibration:** Onboard reference (+5.000 V) with

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PXI/PXIe

- **High‑Speed Sampling:** Up to 80 MS/s per channel with simultaneous acquisition across all four channels. - **High Resolution:** 16‑bit analog‑to‑digital conversion for superior dynamic range and precision. - **Wide Bandwidth:** 40 MHz analog input bandwidth supporting high‑frequency signal capture. - **Large Onboard Memory:** 1 GB shared memory for extended recording durations at full sampling rate. - **Programmable Input Ranges:** ±0.5 V, ±1 V, ±5 V, or ±10 V ranges, software‑selectable. - **Selectable Input Impedance:** 50 Ω or 1 MΩ, software‑configurable for flexible signal interfacing. - **Digital Filtering:** FPGA‑based 10 MHz or 20 MHz digital low‑pass filter options. - **Scatter‑Gather DMA:** High‑speed, continuous data streaming with minimal CPU overhead. - **Triggering Flexibility:** Supports software, analog, external digital, and SSI (System Synchronization Interface) triggers. - **Auto‑Calibration:** Fully automated offset and gain calibration using onboard precision references. - **Synchronization Support:** PLL module (in PCIe‑9834P variant) for precise multi‑card synchronization. - **Software Ecosystem:** Compatible with ADLINK WD‑DASK, LabVIEW, MATLAB, and Visual Studio environments. - **Operating System Support:** Windows XP/7/8/10 (x86/x64) and Linux. - **Environmental Compliance:** RoHS and WEEE compliant; CE and FCC Class A certified.

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PXI/PXIe

- **High Sampling Rate:** Up to 200 MS/s real‑time sampling for single‑channel analog input. - **High Resolution:** 14‑bit ADC providing 1 in 16,384 quantization levels for precise signal representation. - **Input Range & Impedance:** ±1 V input range, 50 Ω ± 2 % impedance, DC‑coupled input. - **Wide Bandwidth:** Analog input bandwidth of 100 MHz (‑3 dB). - **High‑Speed Interface:** PCI Express x4 or PXIe x4 bus interface supporting sustained data throughput up to 400 MB/s. - **Onboard Memory:** 16 K‑sample FIFO buffer for temporary data storage. - **Triggering:** Supports software and external digital triggers; post‑trigger, delay‑trigger, and re‑trigger modes. - **Auto‑Calibration:** Built‑in reference circuit with ±5 ppm/°C drift for automatic offset and gain calibration. - **Scatter‑Gather DMA:** High‑speed, continuous data streaming using bus‑mastering DMA with scatter‑gather capability. - **Auxiliary Digital I/O:** 8‑bit static DIO or 2‑bit synchronous digital input (SDI) for mixed‑signal acquisition. - **Software Support:** Compatible with Windows and Linux; drivers for LabVIEW, MATLAB, and ADLINK DAQPilot. - **Compact Design:** Standard short PCIe card dimensions (106.7 mm × 174.6 mm). - **Connectivity:** Three SMA connectors for analog input, external trigger input, and trigger output. - **Certifications:** CE, FCC Class A, and full EMC/EMI compliance.

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PXI/PXIe

- **PXI Express Specification Rev. 1.0 Compliant:** Ensures full compatibility with PXIe chassis and controllers, supporting high-speed data transfer via PCI Express Gen 1 x4 interface. - **High Sampling Rate:** Up to 100 mega-samples per second (MS/s) per channel, enabling accurate capture of fast transient signals. - **High Resolution:** 14-bit analog-to-digital conversion (ADC) provides fine granularity and high dynamic range for precision measurements. - **Simultaneous 8-Channel Acquisition:** All eight analog input channels can sample concurrently, maintaining phase alignment and timing accuracy. - **Wide Analog Bandwidth:** Up to 100 MHz bandwidth (PXIe-9848), suitable for high-frequency signal analysis. - **Programmable Input Voltage Ranges:** ±0.2 V or ±2 V for PXIe-9848; extended ±100 V range for PXIe-9848H with integrated x15/x50 attenuator module. - **Selectable Input Impedance:** Software-selectable 50 Ω or 1 MΩ input impedance for flexible signal interfacing. - **Large Onboard Memory:** 512 MB acquisition memory (64 MB per channel) for extended data capture without host intervention. - **Scatter-Gather DMA Data Transfer:** High-speed, efficient data streaming to host memory for continuous acquisition. - **Comprehensive Triggering Options:** Supports software, external digital, analog, PXI_STAR, PXI trigger bus, and PXIe_DSTARB sources with multiple trigger modes (pre-, post-, middle, and delay). - **External Digital Trigger Input:** TTL-compatible (3.3 V/5 V), configurable threshold (0.8 V–3.3 V), and polarity selection. - **Auto-Calibration:** Built-in self-calibration ensures long-term measurement accuracy and stability. - **Software and OS Support:** Compatible with Windows and Linux; drivers and SDKs available for LabVIEW™, MATLAB®, C/C++, Visual Basic, and .NET environments. - **High Dynamic Performance:** SINAD up to 65 dB, SNR up to 66 dB, and SFDR up to 74 dB for PXIe-9848; optimized spectral characteristics for PXIe-9848H with attenuator. - **Scalable System Integration:** Multiple PXIe-9848 modules can be synchronized for up to 64 channels in a single 9-slot PXIe chassis.

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PXI/PXIe

- **PXI Express Specification Rev. 1.0 Compliant:** Ensures full compatibility with PXI Express chassis and controllers. - **High Sampling Rate:** Up to 100 MS/s per channel with simultaneous sampling across all eight inputs. - **High Resolution:** 14‑bit ADC resolution (1 in 16,384) for precise signal digitization. - **Wide Bandwidth:** Up to 100 MHz analog input bandwidth (PXIe‑9848); 45 MHz / 35 MHz for PXIe‑9848H with ×15 / ×50 attenuation. - **High Voltage Input Capability:** Programmable input ranges of ±0.2 V, ±2 V, or ±100 V max (PXIe‑9848H). - **Selectable Input Impedance:** 50 Ω or 1 MΩ, software‑configurable. - **Large Onboard Memory:** 512 MB total (64 MB per channel) for extended acquisition sessions. - **Scatter‑Gather DMA:** High‑speed data streaming to host memory with minimal CPU overhead. - **Flexible Triggering:** Supports software, external digital, analog, PXI_STAR, PXIe_DSTARB, and PXI Trigger Bus [0–7] sources. - **Auto‑Calibration:** Fully automated offset and gain calibration using onboard reference circuitry. - **Multi‑Module Synchronization:** Supports synchronization of up to 64 channels in a single 9‑slot PXIe chassis. - **Software Support:** Drivers and SDKs for LabVIEW, MATLAB, C/C++, Visual Basic, and Visual Studio .NET. - **Operating System Compatibility:** Windows 7/8 (x86/x64) and Linux. - **High Dynamic Performance:** SFDR up to 74 dB, SINAD up to 65 dB, ENOB up to 10.6 bits. - **Environmental Robustness:** Operational temperature 0 °C – 55 °C; storage –20 °C – 80 °C. - **Regulatory Compliance:** CE and FCC Class A certified.

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PXI/PXIe

- **High‑Speed Sampling:** Up to 200 MS/s per channel simultaneous sampling. - **High Resolution:** 14‑bit analog‑to‑digital conversion with excellent linearity and dynamic range. - **Dual Analog Inputs:** Two single‑ended channels with software‑selectable coupling (AC/DC) and impedance (50 Ω or 1 MΩ). - **Programmable Input Ranges:** ±0.2 V, ±2 V, or ±10 V full‑scale ranges. - **Wide Bandwidth:** 90 MHz (‑3 dB) analog input bandwidth. - **Large Onboard Memory:** 1 GB shared acquisition memory for high‑speed buffering. - **High Data Throughput:** Continuous streaming up to 800 MB/s via PCIe Gen 2 ×4 interface. - **Scatter‑Gather DMA:** Efficient, CPU‑independent data transfer supporting large, non‑contiguous memory blocks. - **Advanced Triggering:** Software, external digital, analog, and SSI (System Synchronized Interface) triggers with multiple modes (pre‑, post‑, middle‑, and delayed‑trigger). - **External Clocking:** Accepts external reference or sampling clocks (40 MHz–200 MHz). - **Auto‑Calibration:** Fully automated onboard calibration with EEPROM‑stored constants. - **Signal Averaging:** Hardware‑based averaging for noise reduction without CPU overhead. - **Synchronization:** SSI bus for multi‑module synchronization (ACL‑eSSI‑2/3/4 cables). - **Software Support:** Compatible with LabVIEW®, MATLAB®, Visual Studio®, and ADLINK DAQPilot SDK. - **Operating Systems:** Windows XP/7/8 (x86/x64). - **Compliance:** PCI Express 2.0, CE, FCC Class A, RoHS, and WEEE.

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed PXI/PXIe

- **Bus Interface:** Standard AT‑Bus (ISA) - **Analog Inputs:** 16 single‑ended or 8 differential channels - **Analog Outputs:** Two 12‑bit monolithic multiplying D/A channels, double‑buffered - **Digital I/O:** 16 digital inputs and 16 digital outputs, TTL/DTL compatible - **Resolution:** 12‑bit A/D and 12‑bit D/A - **Sampling Rate:** Up to 100 kS/s (single channel) - **Programmable Gain:** ×0.5, ×1, ×2, ×4, ×8 - **Input Range:** Bipolar ±10 V to ±0.625 V; Unipolar 0–10 V to 0–1.25 V - **Trigger Modes:** Software, internal pacer (timer), or external pulse trigger - **Data Transfer Modes:** Polling, DMA, or interrupt‑driven - **Timer/Counter:** Three programmable 16‑bit down counters (Intel 8254 compatible) - **Interrupts:** 9 selectable IRQ levels (IRQ3, 5–7, 9–12, 15) - **DMA Channels:** Selectable DMA 1 or DMA 3 - **Power Supply:** On‑board DC/DC converter for stable analog power - **Connectors:** One 37‑pin D‑type female (analog I/O, timer), two 20‑pin headers (digital I/O) - **Compact Design:** Half‑size PCB (162 mm × 115 mm) - **Software Support:** C‑language library, LabVIEW driver, and Windows DLL development kit (ACLS‑DLL2)

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed ISA

- **Bus Interface:** AT‑Bus (ISA) - **Analog Inputs:** 16 single‑ended or 8 differential channels - **Analog Outputs:** Two 12‑bit double‑buffered D/A channels - **Digital I/O:** 16 digital inputs and 16 digital outputs (TTL/DTL compatible) - **Resolution:** 12‑bit A/D and 12‑bit D/A - **Sampling Rate:** Up to 100 kS/s (single channel) - **Programmable Gain:** - High‑gain programmable amplifier with 8 gain levels: ×0.5, ×1, ×5, ×10, ×50, ×100, ×500, ×1000 - **Input Range (Programmable):** - Bipolar: ±10V, ±5V, ±1V, ±500mV, ±100mV, ±50mV, ±10mV, ±5mV - Unipolar: 0–10V, 0–1V, 0–0.1V, 0–0.01V - **Trigger Modes:** Software, internal pacer (timer), or external trigger - **Data Transfer Modes:** Polling, DMA, or interrupt‑driven - **Timer/Counter:** - 8254 programmable interval timer with three 16‑bit counters - Two cascaded counters for A/D pacer (32‑bit timer, 2 MHz base) - One 16‑bit general‑purpose counter - **Interrupts:** 9 selectable IRQ levels (IRQ3, 5–7, 9–12, 15) - **DMA Channels:** Selectable CH1 or CH3 - **Power Supply:** On‑board DC/DC converter for stable analog power - **Connectors:** - 37‑pin D‑type female connector (analog I/O, counter/timer) - Two 20‑pin IDC connectors (digital I/O) - **Form Factor:** Half‑size ISA card (compact design) - **Software Support:** C‑language library, DOS utilities, LabVIEW driver, and Windows SDK (ACLS‑DLL2)

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed ISA

- **Bus Interface:** AT‑Bus (ISA) compatible. - **Analog Inputs:** 16 single‑ended channels (ACL‑8112PG model). - **Analog Outputs:** Two 12‑bit monolithic multiplying D/A channels with double buffering. - **Digital I/O:** 16 TTL‑compatible digital inputs and 16 TTL‑compatible digital outputs. - **Timer/Counter:** Three programmable 16‑bit down counters (Intel 8254 compatible). - **Sampling Rate:** Programmable up to 100 kHz. - **Resolution:** 12‑bit A/D and 12‑bit D/A conversion. - **Programmable Gain:** Five levels (×1, ×2, ×4, ×8, ×16); ×0.5 selectable via jumper. - **Trigger Modes:** Software, internal pacer (timer‑based), or external pulse trigger. - **Data Transfer Modes:** Polling, DMA, or interrupt‑driven. - **Interrupt Levels:** Selectable from IRQ3, 5–7, 9–12, or 15. - **DMA Channels:** Selectable between Channel 1 or Channel 3. - **Power Supply:** On‑board DC/DC converter for stable analog power. - **Connectors:** One 37‑pin D‑type female connector and two 20‑pin IDC headers. - **Form Factor:** Half‑size ISA card (163 mm × 123 mm). - **Software Support:** C‑language library, DOS utilities, and optional Windows SDK (ACLS‑DLL2) and LabVIEW driver (ACLS‑LVIEW).

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed ISA

- **High‑Speed A/D Conversion:** 12‑bit successive‑approximation ADC (ADS7804 or equivalent) with up to 100 kHz sampling rate. - **Flexible Analog Input Configuration:** 16 single‑ended or 8 differential channels with programmable gain (×1, ×2, ×4, ×8) and bipolar input ranges of ±10 V, ±5 V, ±2.5 V, or ±1.25 V. - **On‑Board FIFO Buffer:** 1 K‑word FIFO memory for gap‑free, high‑speed data acquisition with half‑full and full interrupt flags. - **Dual 12‑bit D/A Outputs:** Two independent DAC2813 (or equivalent) channels, ±10 V or 0–10 V output range, 6 µs settling time, ±5 mA drive. - **Digital I/O:** 16 TTL‑compatible digital input/output lines for control and monitoring. - **Programmable Counter/Timer:** Intel 8254‑compatible 3×16‑bit counters with 2 MHz base clock; supports pacer triggering and event counting. - **DMA and Interrupt Support:** Supports DMA channels 5, 6, 7 and IRQ levels 3, 5–7, 9, 11, 12, 15 for efficient data transfer. - **Auto‑Scanning and Triggering:** Software, internal pacer, or external trigger modes; automatic channel scanning for sequential sampling. - **Integrated DC/DC Converter:** Provides stable analog power isolation from digital circuitry. - **Compact Half‑Size ISA Form Factor:** 163 mm × 123 mm PCB with 37‑pin D‑type and dual 20‑pin IDC connectors. - **Software Support:** Includes DOS C/C++ library, Windows DLL (ACLS‑DLL2), and LabVIEW driver (ACLS‑LVIEW).

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed ISA

- **High‑Speed A/D Conversion:** 12‑bit resolution with up to 100 kS/s sampling rate using a Burr‑Brown ADS7804 or equivalent successive‑approximation ADC. - **Channel Configuration:** 16 single‑ended (SE) or 8 differential (DI) analog input channels, selectable via jumper (JP7). - **On‑Board FIFO Buffer:** 1K‑word FIFO memory for continuous, gap‑free data acquisition with half‑full and full interrupt flags. - **Programmable Gain Amplifier:** Software‑selectable gains of ×1, ×2, ×4, ×8 for input ranges of ±10 V, ±5 V, ±2.5 V, ±1.25 V. - **Triggering Flexibility:** Supports software, internal pacer (timer‑based), and external trigger modes for A/D conversion. - **Data Transfer Options:** Software polling, interrupt‑driven, FIFO polling, FIFO half‑full interrupt, or DMA (Direct Memory Access) transfer. - **Digital I/O:** 16 TTL‑compatible digital input and 16 TTL‑compatible digital output channels. - **Timer/Counter:** Three independent 16‑bit programmable down counters (Intel 8254 compatible) with a 2 MHz base clock; two cascaded for A/D pacer timing, one user‑programmable. - **Interrupt and DMA Support:** Selectable IRQ levels (3, 5–7, 9, 11, 12, 15) and DMA channels (5, 6, 7). - **Power and Stability:** On‑board DC/DC converter for stable analog power isolation from digital noise. - **Compact Design:** Half‑size ISA card (163 mm × 123 mm) with 37‑pin D‑type and dual 20‑pin IDC connectors. - **Software Support:** Includes DOS C/C++ library, Windows DLL (ACLS‑DLL2), and LabVIEW driver (ACLS‑LVIEW).

Manufacturer: Adlink Technology Inc.

Category: A/D High Speed ISA